Multiwii Identity Multiwii Motor Pins navigation bar

Table of Contents

Multiwii IMU

Gets raw IMU sensor data from the auto-pilot.

Library

QUARC Targets/Communications/Multiwii

MATLAB Command Line

Click to copy the following command line to the clipboard. Then paste it in the MATLAB Command Window:

qc_open_library('quarc_library/Communications/Multiwii')

Description

Multiwii IMU

The Multiwii IMU block uses the Multiwii protocol on the input stream to send a command to the aircraft to get raw IMU sensor data from the auto-pilot. The Multiwii IMU block sends an MSP_RAW_IMU message to the auto-pilot.

This block is designed to be used with blocking I/O. It is typically used with a stream connected to a serial port. To open the stream a Multiwii Connect block should be used.

The outputs of the block are the raw accelerometer, gyroscope and magnetometer readings. Each output is a 3-vector of the x, y and z components of the three axis measurements. The units depend on the particular sensor used.

A copy of the stream is also output so that the Multiwii blocks may be chained together.

If an error occurs, then the block returns a negative error code at its err output. The Compare to Error block may be used to check for specific error codes. If the stream is not valid because it is not yet connected, the err output will be zero since this condition is expected and the validity of the stream may be checked using the con output of the Multiwii Connect block.

Helpful Hints

Other uses of this block

Hint Although it is intended for use in the main diagram with the other Multiwii blocks, the Multiwii IMU block may be used with the Advanced stream blocks, even in an asynchronous thread.

Input Ports

stm

A reference to the stream created by the Multiwii Connect block. If a connection has not yet been established, then the err output of the Multiwii IMU block will be zero.

Output Ports

stm

A reference to the stream. This output is merely a copy of the stm input. Providing this output makes it much easier to establish the execution order of Multiwii blocks in the diagram because Simulink generally executes daisy-chained blocks in sequence.

acc

A 3-vector value containing the raw accelerometer values in the x, y and z axes respectively. The units depend on the device.

gyr

A 3-vector value containing the raw gyroscope values in the x, y and z axes respectively. The units depend on the device.

mag

A 3-vector value containing the raw magnetometer values in the x, y and z axes respectively. The units depend on the device.

err

An int32 value indicating whether the data was read successfully. This value will be positive if data was read successfully. It will be zero if data could not be read immediately. If an error occurs then this value is a negative error code. See Error Codes for the different error codes and their values. Use the Compare to Error block rather than the error code itself to check for specific error codes. To check for errors in general use the Compare to Zero block to check whether the err output is less than zero.

Parameters and Dialog Box

Multiwii IMU

The Multiwii IMU block has no parameters.

Targets

Target Name

Compatible*

Model Referencing

Comments

QUARC Win32 Target

Yes

Yes

QUARC Win64 Target

Yes

Yes

QUARC Linux Nvidia Target

Yes

Yes

QUARC Linux QBot Platform Target

Yes

Yes

QUARC Linux QCar 2 Target

Yes

Yes

QUARC Linux QDrone 2 Target

Yes

Yes

QUARC Linux Raspberry Pi 3 Target

Yes

Yes

QUARC Linux Raspberry Pi 4 Target

Yes

Yes

QUARC Linux RT ARMv7 Target

Yes

Yes

QUARC Linux x64 Target

Yes

Yes

QUARC Linux DuoVero Target

Yes

Yes

QUARC Linux DuoVero 2016 Target

Yes

Yes

QUARC Linux Verdex Target

Yes

Yes

QUARC QNX x86 Target

Yes

Yes

Last fully supported in QUARC 2018.

Rapid Simulation (RSIM) Target

Yes

Yes

S-Function Target

No

N/A

Old technology. Use model referencing instead.

Normal simulation

Yes

Yes

* Compatible means that the block can be compiled for the target.

See Also

 

navigation bar